Woven bag mixer operating procedures
First, the start-up power supply will be equipped for warm-up.
2. Prepare the ingredients according to the ingredients ratio.
3. Pour the prepared ingredients into a mixing bucket.
4. Start the switch to stir the material in the barrel to make it even.
Fifth, open the gate valve of the discharge port, and join the mixed material to the feeding port of the wire drawing machine.
平膜机操作规程塑料编织袋 Woven bag flat film machine operating procedures
1. Install the imported mold at the front of the flat film machine.
2. Introspect the filter or change the filter.
Third, arrange the cutting knife first
4. Turn on the power to warm up. The warm-up time is set as requested in the equipment imitation list.
Fifth, after warming up to time, start the transmission system according to the set method.
Six, pull out the diaphragm into the water tank to cool.
7. The driving roller is twisted, the diaphragm is pulled and cut into wires.
8. The silk is drawn into the setting box after being pulled.
Nine, the wire is separated and introduced into the tube of the winding machine.
绕卷机操作规程 Operating rules for woven bag winding machine
First, start the power supply, so that the tube shaft on the machine starts to migrate and change.
2. Wrap the silk on the tube quickly.
Third, the wire on the tube is quickly taken to a certain degree and replaced with a new tube.
4. Stack the coiled tubes as specified.
圆织机操作规程 Operating Rules for Woven Bag Circular Loom
First, press the power switch to make it run intermittently at low speed, and check for failures.
2. During the shutdown, the tube with the wire is led from the lowest row of warp wires to the guide plate of the head of the frame, and it is introduced into the specification ring on the surface, pulled up in the middle position and knotted.
3. Install the shuttle, and leave the warp thread between the specification ring and the bracket.
Fourth, weft the shuttle, leave the left end hole of the warp tube, pull out the seat, and then tighten the spring at the right end.
5. Insert the weft thread into the roller through the porcelain bottle, tighten the wire end in the groove, and click the button of the golden diamond woven bag to turn the shuttle 90 degrees to pull the weft thread out of the loom.
6. Adjust the specification ring to make the width reach the request.
7. Press the linkage switch to make the garden loom and the cloth rolling machine start to run at the same time, and enter the abnormal weaving and winding.
热切机操作规程 Operating rules for woven bag hot cutting machine
1. Place the piece of cloth on the rack of the front shaft of the hot cutter.
Second, adjust the useful width of the wire between the two ends of the cutting wire and the length limit rod.
3. Wrap the cloth around the roller, turn on the power, and make the roller run.
4. When the cloth reaches the limit length lever, press the wire cutter.
Fifth, the semi-finished product after the blocking is quickly pushed down the eager machine and inherits the operation.
Sixth, the power is cut off and the number of semi-finished products is counted.
工业缝纫机操作规程 Operating rules for woven bag industrial sewing machine
1. Thread the cotton thread into the needle nose.
2. Put the bottom end of the bag into the presser foot and sew according to the requested size.
3. Turn on the power to make the machine run.
Four, 100 bags of each sewing machine shut down and shut down, and lift the presser foot.
Fifth, cut off the wiring between the bag and the bag, check the number.
Woven bag printing machine operating procedures
First, paste the carved printing plate on the suitable position of the cylinder.
2. After the ink is adjusted, pour the ink into the oil box and open the power supply to make the ink evenly spread on the roller.
编织袋 放在运送板上，启动运送开关，使金钻编织袋徐徐进入机口印字。 3. The woven bag is placed on the conveying board, and the conveying switch is activated, so that the golden diamond woven bag slowly enters the machine to print.
Fourth, adjust the printing plate status and ink at any time. plastic woven bag